Home / Federal careers / WG-2606
Electronic Industrial Control Mechanic
This standard covers nonsupervisory work involved in the installation, maintenance, troubleshooting, repair, and calibration of electronic controls and indicating and recording systems used on industrial machinery or engines, in automated materials storage and handling systems, in aircraft engine and similar test facilities, or in energy monitoring and control systems. This work requires knowledge of the practical application of electronics theories and circuits that are applicable to power, tim
What WG-2606 pays
Federal Wage System pay is set by local prevailing wage surveys, so it moves with the wage area rather than a national table.
Wage Grade rates are published per wage area rather than nationally, so the number that matters is the one for the installation you are applying to.
Source: DoD Civilian Personnel Advisory Service wage schedules.
Qualification requirements
OPM's standard for WG-2606, as written.
Electronic Industrial Control Mechanic
Federal Wage System Position
Work Performed
This standard covers nonsupervisory work involved in the installation, maintenance, troubleshooting, repair, and calibration of electronic controls and indicating and recording systems used on industrial machinery or engines, in automated materials storage and handling systems, in aircraft engine and similar test facilities, or in energy monitoring and control systems. This work requires knowledge of the practical application of electronics theories and circuits that are applicable to power, timing, motion control, indicating devices, and pulse and counting mechanisms, including special purpose digital computers (microprocessors) dedicated to control functions, as well as a knowledge of industrial equipment operation and processes.
Working Conditions
: Work is usually performed inside in well lighted, heated, and ventilated areas. When equipment is fixed in place, it is sometimes necessary to work in warehouse or industrial areas exposed to loud noises, heat or cold, fumes, etc. Employees are subject to injuries, such as electric shock, cuts and bruises, as well as burns caused by electrical energy or soldering irons. ELECTRONIC INDUSTRIAL CONTROLS MECHANIC,
What this means if you served
- Write the duties, not the billet. OPM credits military experience on the work performed, and does not use rank or pay to judge specialized experience.
- Put the training and certifications you earned in service on the page. They count here.
- Claim your veterans preference on the application. It is not applied for you.
- No positive education requirement here, so qualifying experience can stand in for the education.
How to qualify for WG-2606
1Review Trade/Craft Requirements
WG positions require demonstrated skill in a specific trade or craft. Review the job announcement for required certifications, licenses, and hands-on experience.
2Document Your Experience
WG positions are experience-based, not grade-based. Document your years of hands-on trade experience, apprenticeships completed, and journeyman status if applicable.
3Gather Credentials
Collect your DD-214, trade certifications (welding, electrical, HVAC, etc.), apprenticeship completion certificates, and any specialized licenses required for your trade.
4Build Your Federal Resume
Two pages, the same USAJOBS limit that has applied since 27 September 2025. Lead with hands-on trade experience: the tools and equipment you ran, safety training, the projects you finished, and hours worked per week.
5Apply on USAJOBS
Search for WG positions in your trade specialty, carefully answer assessment questions about your skill level and experience, and submit before the closing date.
Military jobs that map to this series
Interior Communications Electrician
WG-2606 Electronic Industrial Control Mechanic fits synchro, motor-control, and indicator-system experience specifically.
Skills that carry over: Industrial control systems, Synchro and servo systems, Motor controls, Electromechanical repair.
Usually opens at: WG-8, WG-10, WG-11.
Radio Equipment Repairer
WG-2606 Electronic Industrial Controls Mechanic fits 94Es who repaired control and power-electronics subsystems at the component level.
Skills that carry over: Component-level repair, Electronic controls, Fault isolation, Soldering and rework.
Usually opens at: WG-8, WG-10, WG-11.
Missile and Space Systems Electronic Maintenance
WG-2606 Electronic Industrial Control Mechanic suits technicians moving into automated industrial control electronics.
Skills that carry over: Industrial control electronics, Fault isolation, Calibration, Preventive maintenance.
Usually opens at: WG-8, WG-10.
Your record can qualify you even when your code is not on this list. The crosswalk is a starting point, not the gate.
Typical duties
- Perform electronic industrial control mechanic tasks as assigned
- Follow safety procedures and regulations
- Maintain and operate tools and equipment
- Complete work orders and documentation
- Coordinate with team members and supervisors
Key competencies
Ability to follow safety procedures and regulations
Knowledge of tools and equipment for the trade
Skill in performing physical tasks requiring manual dexterity
Ability to work independently and as part of a team
Ability to read and interpret instructions and procedures
Words the announcement will use
Use the ones your record actually supports. A rater is matching your experience against the specialized experience statement, and a keyword with nothing behind it does not survive that.
Questions about WG-2606
What is an Electronic Industrial Control Mechanic?
An Electronic Industrial Control Mechanic (WG-2606) installs, maintains, troubleshoots, repairs, and calibrates electronic controls and recording systems used on industrial machinery, automated storage systems, aircraft engine test facilities, and energy monitoring systems. They work with timing circuits, motion controls, and microprocessor-based control systems.
How much does a federal Electronic Industrial Control Mechanic make?
WG-2606 positions are paid under the Federal Wage System based on local prevailing rates. Journeyman-level wages (WG-10/11) typically range $28-$42 per hour depending on locality. Annual earnings range $58,000-$87,000. Industrial automation specialists often command premium rates.
What are the requirements for WG-2606 positions?
WG-2606 requires knowledge of electronics theories and circuits applicable to power, timing, and motion control systems. Qualifications include experience with indicating devices, microprocessors dedicated to control functions, and understanding of industrial equipment operation and processes.
Can military experience substitute for education in WG-2606?
Yes, military industrial control experience qualifies. MOSs involving shipboard engineering controls, aircraft ground support equipment, or automated systems maintenance provide relevant experience. Navy GSE/GSM ratings, Army 91 series equipment mechanics, and Air Force power production specialists have transferable skills.
What is the career progression for Electronic Industrial Control Mechanic?
Electronic Industrial Control Mechanics progress from helper (WG-5) through journeyman (WG-10/11) based on demonstrated skill. Senior positions (WG-12+) involve complex automation systems or lead roles. Many advance to GS engineering technician positions or industrial control systems management.
How do I apply for WG-2606 jobs on USAJOBS?
Search USAJOBS for 'Electronic Industrial Control' or series '2606.' Positions exist at shipyards, depot maintenance facilities, manufacturing plants, and test facilities. Highlight PLC programming, industrial automation experience, and control systems troubleshooting skills. Veterans receive preference.
Ready to apply for WG-2606?
A rater matches your record against the announcement's specialized experience statement, inside two pages. BMR writes that shape from your own experience: competency headers, real scope, hours per week, and the supervisor detail the rater checks.